1、 三菱 C6C64C64T 三菱 C6C64C64T DDB接口說明書
This is a parameter for the maximum spindle speed of each gear step. (This corresponds to the setup paramet er, spindle parameter smax1 to 4.) The CNC creates the spindle gear shift command 1
This is a parameter for the maximum spindle speed of each gear step. (This corresponds to the setup paramet er, spindle parameter smax1 to 4.) The CNC creates the spindle gear shift command 1
2、 三菱 C6C64C64T 三菱 C6C64C64T DDB接口說明書
(Note 1) The unit systems B and C are settings for t he setup parameters (basic specification parameters: #1003 iunit). This may differ according to the machine type. (Note 2) The un
(Note 1) The unit systems B and C are settings for t he setup parameters (basic specification parameters: #1003 iunit). This may differ according to the machine type. (Note 2) The un
3、 三菱 C6C64C64T 三菱 C6C64C64T DDB接口說明書
(Note 1) The unit systems B and C are settings for t he setup parameters (basic specification parameters: #1003 iunit). This may differ according to the machine type. (Note 2) The un
(Note 1) The unit systems B and C are settings for t he setup parameters (basic specification parameters: #1003 iunit). This may differ according to the machine type. (Note 2) The un
4、 三菱 C6C64C64T 三菱-C6C64C64T PLC接口說明書(eng)
Introduction This manual describes the various signal interfaces and functions required when creating MELDAS C6/C64/C64T sequence programs (built-in PLC). Read this manual thoroughly bef
Introduction This manual describes the various signal interfaces and functions required when creating MELDAS C6/C64/C64T sequence programs (built-in PLC). Read this manual thoroughly bef
5、 三菱 C6C64C64T 三菱 C6C64C64T 編程說明書 (M系)
For items described in "Restrictions" or "Usable State", the instruction manual issued by the machine manufacturer takes precedence over this manual. An effort has been made to note as man
For items described in "Restrictions" or "Usable State", the instruction manual issued by the machine manufacturer takes precedence over this manual. An effort has been made to note as man
6、三菱 C6C64C64T 三菱 C6C64C64T 參數說明書
(1) Word and address A word is a collection of characters arranged in a specific sequence. This entity is used as the unit for processing data and for causing the machine to execute specifi
(1) Word and address A word is a collection of characters arranged in a specific sequence. This entity is used as the unit for processing data and for causing the machine to execute specifi
7、三菱 C6C64C64T 三菱 C6C64C64T 參數說明書(eng).pdf
Set up a compensation factor for reducing a control error in the reduction of a corner roundness and arch radius. Indicates a maximum control error (mm) in parentheses. The larger the
Set up a compensation factor for reducing a control error in the reduction of a corner roundness and arch radius. Indicates a maximum control error (mm) in parentheses. The larger the
8、三菱 C6C64C64T 三菱 C6C64C64T 連接維護說明書
Correctly connect the output side (terminal U, V, W). The servomotor will not run properly if incorrectly connected. Always install an AC reactor per each power supply unit. Alw
Correctly connect the output side (terminal U, V, W). The servomotor will not run properly if incorrectly connected. Always install an AC reactor per each power supply unit. Alw
9、三菱 C6C64C64T 三菱 C6C64C64T 使用說明書
If the tool compensation amount is changed during automatic operation (including single block stop), the amount will be validated from the next block or several blocks following. If the
If the tool compensation amount is changed during automatic operation (including single block stop), the amount will be validated from the next block or several blocks following. If the
10、三菱 C6C64C64T 三菱 C6C64C64T 網絡使用說明書.pdf
For items described as "Restrictions" or "Usable State" in this manual, the instruction manual issued by the machine maker takes precedence over this manual. Items not described in th
For items described as "Restrictions" or "Usable State" in this manual, the instruction manual issued by the machine maker takes precedence over this manual. Items not described in th
11、三菱 C70系列 三菱 C70系列 編程說明書(L系)
Your MITSUBISHI ELECTRIC product is designed and manufactured with high quality materials and components which can be recycled and/or reused. This symbol means that batteries and accumulator
Your MITSUBISHI ELECTRIC product is designed and manufactured with high quality materials and components which can be recycled and/or reused. This symbol means that batteries and accumulator
12、三菱 C70系列 三菱 C70系列 編程說明書(L系)
(注1) 英制/公制的切換，可通過參數畫面進行(#1041 I_inch；僅接通電源時有效)，也可通過G指令(G20,G21) 進行。 但是、通過G指令只可以切換輸入指令單位、無法實現輸入設定單位的切換。因此、刀具偏置量等補償 量及變量數據，請預先按照輸入設定單位進行設定。 (注2) 公制單位與英制單位不能并用。 (注3) 當在輸入指令單位不同的軸之間進行圓弧插補時，
(注1) 英制/公制的切換，可通過參數畫面進行(#1041 I_inch；僅接通電源時有效)，也可通過G指令(G20,G21) 進行。 但是、通過G指令只可以切換輸入指令單位、無法實現輸入設定單位的切換。因此、刀具偏置量等補償 量及變量數據，請預先按照輸入設定單位進行設定。 (注2) 公制單位與英制單位不能并用。 (注3) 當在輸入指令單位不同的軸之間進行圓弧插補時，
