1、三菱 SH 三菱-SH(NA)-080339
z 在符合所用CPU模塊的用戶手冊中規定的一般操作環境規格下使用PLC 在一般規格范圍之外的環境中使用 PLC可能會引起電擊 火災 故障 并會損壞模塊 或 使模塊性能變差 z 安裝模塊時 按住模塊下部的安裝桿 將模塊的鎖緊扣插進基板安裝孔中扣牢 如果模塊安裝得不正確 可能導致故障 損壞或使模塊松動 跌落下來 如果用在可能一直振動的環境中 則要用螺釘緊固模塊
z 在符合所用CPU模塊的用戶手冊中規定的一般操作環境規格下使用PLC 在一般規格范圍之外的環境中使用 PLC可能會引起電擊 火災 故障 并會損壞模塊 或 使模塊性能變差 z 安裝模塊時 按住模塊下部的安裝桿 將模塊的鎖緊扣插進基板安裝孔中扣牢 如果模塊安裝得不正確 可能導致故障 損壞或使模塊松動 跌落下來 如果用在可能一直振動的環境中 則要用螺釘緊固模塊
2、三菱 SH 三菱-SH(NA)-080407
[設計注意事項] ! 危險 • 不要把數據寫入智能功能模塊緩沖存儲器的 只讀區 此外 不要打開或關閉傳送到PLC CPU或從PLC CPU傳出的輸入/輸出信號中的 保留 信號 這樣做可能使PLC 發生系統故障 • 依據外部輸出晶體管的故障情況 則有輸出為ON或OFF狀態的情況 對可能導致重大事故的 輸出信號安裝外部監視回路
[設計注意事項] ! 危險 • 不要把數據寫入智能功能模塊緩沖存儲器的 只讀區 此外 不要打開或關閉傳送到PLC CPU或從PLC CPU傳出的輸入/輸出信號中的 保留 信號 這樣做可能使PLC 發生系統故障 • 依據外部輸出晶體管的故障情況 則有輸出為ON或OFF狀態的情況 對可能導致重大事故的 輸出信號安裝外部監視回路
3、三菱 SH 三菱-SH(NA)-08041
[設計注意事項] ! 危險 在可編程控制器外部配置安全回路 使整個系統在外部電源出錯或PLC故障時也能安全運行 不遵守這一點可能導致不正確輸出或故障 引發事故 1 配置緊急停止回路和互鎖回路 諸如定位控制上限/下限 以防止PLC外部的機械損 壞 2 OPR運行受OPR指令和OPR速度數據控制 當近點狗變成ON時減速起動 因此 如果未正
[設計注意事項] ! 危險 在可編程控制器外部配置安全回路 使整個系統在外部電源出錯或PLC故障時也能安全運行 不遵守這一點可能導致不正確輸出或故障 引發事故 1 配置緊急停止回路和互鎖回路 諸如定位控制上限/下限 以防止PLC外部的機械損 壞 2 OPR運行受OPR指令和OPR速度數據控制 當近點狗變成ON時減速起動 因此 如果未正
4、三菱 SH 三菱-SH(NA)-080446ENG
controller, be sure to read the manual carefully and thoroughly confirm the safety. Especially in the above mentioned control operations that are performed from an external device to a remot
controller, be sure to read the manual carefully and thoroughly confirm the safety. Especially in the above mentioned control operations that are performed from an external device to a remot
5、三菱 SH 三菱-SH(NA)-080446ENG
controller, be sure to read the manual carefully and thoroughly confirm the safety. Especially in the above mentioned control operations that are performed from an external device to a remot
controller, be sure to read the manual carefully and thoroughly confirm the safety. Especially in the above mentioned control operations that are performed from an external device to a remot
6、三菱 SH 三菱-SH(NA)-080578ENG
Be sure to tighten the screws using the specified torque. If the screws are loose, it may cause a short circuit, malfunctions or a drop of the module. Overtightening the screws may damage the
Be sure to tighten the screws using the specified torque. If the screws are loose, it may cause a short circuit, malfunctions or a drop of the module. Overtightening the screws may damage the
7、三菱 SH 三菱-SH(NA)-080644ENG
Do not bunch the control wires or communication cables with the main circuit or power wires, or install them close to each other. They should be installed 100 mm (3.94 inch) or more from each o
Do not bunch the control wires or communication cables with the main circuit or power wires, or install them close to each other. They should be installed 100 mm (3.94 inch) or more from each o
8、三菱 SH 三菱-SH(NA)-080647ENG
[DESIGN PRECAUTION] DANGER Do not write data into the "system area" of the buffer memory of intelligent function modules. Also, do not use any "prohibited to use" signals as an output signa
[DESIGN PRECAUTION] DANGER Do not write data into the "system area" of the buffer memory of intelligent function modules. Also, do not use any "prohibited to use" signals as an output signa
9、三菱 SH 三菱-SH(NA)-080647ENG
[DESIGN PRECAUTION] DANGER Do not write data into the "system area" of the buffer memory of intelligent function modules. Also, do not use any "prohibited to use" signals as an output signa
[DESIGN PRECAUTION] DANGER Do not write data into the "system area" of the buffer memory of intelligent function modules. Also, do not use any "prohibited to use" signals as an output signa
10、三菱 SH 三菱-SH(NA)-080648ENG
A - 1 [DESIGN PRECAUTION] DANGER Do not write data into the "system area" of the buffer memory of intelligent function modules. Also, do not use any "prohibited to use" signals as an out
A - 1 [DESIGN PRECAUTION] DANGER Do not write data into the "system area" of the buffer memory of intelligent function modules. Also, do not use any "prohibited to use" signals as an out
11、三菱 SH 三菱-SH(NA)-080683ENG
Provide a safety circuit outside the programmable controller so that the entire system will opera safely even when an external power error or programmable controller failure occurs. Failure to
Provide a safety circuit outside the programmable controller so that the entire system will opera safely even when an external power error or programmable controller failure occurs. Failure to
12、三菱 SH 三菱-SH(NA)-080699ENG
[DESIGN PRECAUTIONS] DANGER Do not write data into the "system area" of the buffer memory of intelligent function modules. Also, do not use any "prohibited to use" signals as an output signal t
[DESIGN PRECAUTIONS] DANGER Do not write data into the "system area" of the buffer memory of intelligent function modules. Also, do not use any "prohibited to use" signals as an output signal t
